Other

SRAM's BlipBox is the control module that turns your triathlon or time trial machine into a wireless missile. Connected to SRAM RED eTap Blip remote shifters, the BlipBox manages the wireless shifting via AIREA, SRAM’s proprietary communication protocol, allowing immediate shifts from nearly any aero position. - BlipBox mount included - Replaces standard drop bar shift levers - Limitless aero configurations - Up to two positions per side - Fits a standard Garmin mount or the included mount

RockShox Reverb Service Kits - 12 of Each size Key, 3 Top Cap Assemblies, 10 Blue 1-Piece IFPs, 10 Foam Rings, 10 Inner Seal U-Cups, 10 Inner Seal Head Bushings, 10 Inner Seal Head O-Rings, 10 Strain Relief Barbs, 10 Remote Barbs, 10 Bleed Screws, 10 Air Valve Caps, 6 Seat Bolts and Nuts, 10 Main Piston O-Rings

The VukaClip is all about providing the ultimate in fit, security, and adjustability for you to be faster and more efficient in your triathlon or time-trial aero position at an affordable price. Redesigned to be easier to set up and adjust. The VukaClip is available with an above-bar or below-bar mounting system for achieving an optimized aero position. The VukaClip also has a large, redesigned armrest to reduce pressure points and increase comfort. The VukaClip is made with the industry-standard 22.2mm clamp diameter for maximum versatility, making it compatible with Vuka Alumina extensions, the Vuka Carbon Extensions as well as most extensions on the market. Features - Fit, security, and adjustability - Above-bar or below-bar mounting system - Compatible with most extensions

- Includes 61803 bearings and one grease syringe - Measurable wattage savings between 1.5 and 9 watts per bearing set, depending on the level and condition of your existing bearings - Note: 88 front and 188v9 rear hubs are on all 2014 and newer Zipp 202, 303, 404, 808 - One kit required for: Zipp 88, 30 and 60 front hubs Zipp 188v8 rear hubs Zipp ALL free hub driver bodies - These 61803 bearings are not interchangable with the 77/177 hub 61803 bearings

- Includes 61903 bearings and one grease syringe - Measurable wattage savings between 1.5 and 9 watts per bearing set, depending on the level and condition of your existing bearings - Note: 88 front and 188v9 rear hubs are on all 2014 and newer Zipp 202, 303, 404, 808 - One kit required for: Zipp 188v9, 30 and 60 rear hubs

- Includes 61803 (1) and 61903 (1) bearings and one grease syringe - Measurable wattage savings between 1.5 and 9 watts per bearing set, depending on the level and condition of your existing bearings - Note: 88 front and 188v9 rear hubs are on all 2014 and newer Zipp 202, 303, 404, 808 - One kit required for: Zipp Super-9, 900 tubular and Sub-9 disc rear hubs

Wrist Comfort Bend provides easy hand clearance for a more-relaxed aero bar setup. They are especially suitable for a wide-aero setup. This extension shape is supplied as a standard with the super-adjustable Vola aero bar, which won ‘Best of Show’ at Eurobike 2013. - Pro version is alloy, with shot-peened, black anodized finish. - Team version is carbon The kit comprises clamps, new comfort cradles and silicone pads, wrist comfort bend extensions, and all fixing hardware. Stack height can be adjusted in the range 57–87 mm using the Riser Kit (separately available).

Upgrade your BB30 bottom bracket to the long-lasting smoothness of FSA Ceramic Bearings. Lighter and harder than steel, ceramic bearings can reduce friction, increase durability, and lighten your bike. What's not to like?

The Airstryke II takes the features of the ever popular Airstryke and adds an expanded fit range and more comfortable armrest. The flip up bracket and classic shape are retained. Performance The Airstryke II is intended to allow riders to add aerobars to their road or adventure bike without sacrificing the ability to hold the bars close to the stem. The comfortable grip angle and smoothly curved armrest offer a relaxed position for long days in the saddle. Fit Data - Armrest Offset: -85mm to 17.5mm in 7.5mm steps - Armrest Width: 131mm to 298mm in 18.5mm steps - Armrest Stack: 40mm Origin As one of the most popular model in the history of aerobars it seemed appropriate to update the much loved Airstryke with our new generation fit range and comfort focused armrest. We didn't want to change the elements that have made the bar so successful and the changes made just enhance the adjustability and comfort. - Bracket: L2 Flip-Up - Clamp Diameter: 31.8mm (26.0 w/Shims) - Armrest: Ergo Armrest - Armrest Stack: 40mm - Reach: -85mm to 17.5mm in 7.5mm steps - Extension Adjustment: 150mm (center of basebar - end) - Armrest Width: 155mm - 203mm - Weight: 592g

The RockShox AXS controller ushers in the next generation of a clean cockpit with a completely cable-free design. With the touch of a button, operate the new Reverb AXS seatpost with less effort than ever before. Open up all the possibilities with AXS. - AXS app lets you customize configurations, monitor battery levels, update firmware and much more for all RockShox and SRAM AXS enabled components - Compatible with Matchmaker X - System is completely water and dust proof to IP69K

105 piece assortment of 1-1/8-inch aluminum headset spacers. Kit includes: - 1.5mm (Silver) qty. 15 - 2.5mm (Silver) qty. 15 - 5mm (Silver) qty. 15 - 7.5mm (Silver) qty. 5 - 10mm (Silver) qty. 5 - 1.5mm (Black) qty. 15 - 2.5mm (Black) qty. 15 - 5mm (Black) qty. 15 - 7.5mm (Black) qty. 5

Our new Sonic bracket has been designed as the successor to the J2, which has been a somewhat ignored part of our range. With this update it brings our new generation fit range to a wider range of price points, replacing the J2 bracket. The Ergo armrest has been created to offer both a huge upgrade in fit range as well as increased rider comfort with a supportive curve to cup the arms. Performance - The Sonic/Ergo is designed to present minimal frontal area to create as little aerodynamic drag as possible. The main purpose of an aerobar is, of course, to get the rider into a fast position. Despite a fairly minimalist appearance, the Sonic/Ergo offers a comprehensive fit range for exactly this purpose. Fit Data - Armrest Offset: -70mm to -2.5mm in 7.5mm steps - Armrest Width: 124mm to 290mm in 18.5mm steps (With Extensions at 100mm) - Armrest Stack: 60mm (no riser kit) to 130mm in 5mm increments (With aftermarket Riser Kit) - The extension length and rotation can be easily adjusted using the top bolt. There are 100 distinct position options achievable just by moving the armrests. Combine that with the risers and this bar offers 1500 possible configurations. As a clip-on bar it is also possible to adjust the extension width and tilt easily. This is the most adjustable clip-on bar on the market (and in history). It is worth noting that our previous top level clip-on aerobar, the J4/F35, offered 90 possible configurations. This highlights the significant step forward we’ve made with our new generation aerobars in allowing riders to precisely adjust their position. Origin - After we released the Supersonic (J5) as a premium bracket with market-leading fit options and versatility, we wanted to bring the same kind of options to the rest of our range of brackets and thus aerobars. By simplifying the extension clamp and shifting the wing forward to the bar center line, we were able to meet our targets. As a consequence of the simplification the Sonic is the lightest of our current brackets. The Ergo armrest shares the flippable design of the rest of our new generation armrests. By swapping sides or rotating the armrests, smaller increments of movement are achieved – making it simple to fine-tune a rider's position or match the position from their previous aerobar or bike. Extensions - Extension Shape: A 35 degree ski-bend extension suited to riders who prefer to adopt a wrist angle that is on the low side of the neutral range. - The 35a is a straight 35° bend. - Bracket: Sonic - Clamp Diameter: 31.8mm (26.0 w/Shims) - Armrest: Ergo / 10mm Pads - Armrest Width: 124mm to 290mm in 18.5mm steps (with Extensions at 100mm) - Armrest Offset: -70mm to -2.5mm in 7.5mm steps - Armrest Stack: The minimum is 60mm and the bracket is compatible with our existing risers which add up to 130mm stack with (70mm of spacers added) - Weight: 559g

Our new Sonic bracket has been designed as the successor to the J2, which has been a somewhat ignored part of our range. With this update, it brings our new generation fit range to a wider range of price points, replacing the J2 bracket. The Ergo armrest has been created to offer both a huge upgrade in fit range as well as increased rider comfort with a supportive curve to cup the arms. Performance - The Sonic/Ergo is designed to present minimal frontal area to create as little aerodynamic drag as possible. The main purpose of an aerobar is, of course, to get the rider into a fast position. Despite a fairly minimalist appearance, the Sonic/Ergo offers a comprehensive fit range for exactly this purpose. Fit Data - The extension length and rotation can be easily adjusted using the top bolt. There are 100 distinct position options achievable just by moving the armrests. Combine that with the risers and this bar offers 1500 possible configurations. As a clip-on bar it is also possible to adjust the extension width and tilt easily. This is the most adjustable clip-on bar on the market (and in history). It is worth noting that our previous top level clip-on aerobar, the J4/F35, offered 90 possible configurations. This highlights the significant step forward we’ve made with our new generation aerobars in allowing riders to precisely adjust their position. Origin - After we released the Supersonic (J5) as a premium bracket with market-leading fit options and versatility, we wanted to bring the same kind of options to the rest of our range of brackets and thus aerobars. By simplifying the extension clamp and shifting the wing forward to the bar center line, we were able to meet our targets. As a consequence of the simplification the Sonic is the lightest of our current brackets. The Ergo armrest shares the flippable design of the rest of our new generation armrests. By swapping sides or rotating the armrests smaller increments of movement are achieved – making it simple to fine tune a riders position or match the position from their previous aerobar or bike. - Bracket: Sonic - Clamp Diameter: 31.8mm (26.0 w/Shims) - Armrest: Ergo / 10mm Pads - Armrest Width: 124mm to 290mm in 18.5mm steps (with Extensions at 100mm) - Armrest Offset: -70mm to -2.5mm in 7.5mm steps - Armrest Stack: The minimum is 60mm and the bracket is compatible with our existing risers which add up to 130mm stack with (70mm of spacers added) - Weight: 559g

Our new Sonic bracket has been designed as the successor to the J2, which has been a somewhat ignored part of our range. With this update, it brings our new generation fit range to a wider range of price points, replacing the J2 bracket. The Ergo armrest has been created to offer both a huge upgrade in fit range as well as increased rider comfort with a supportive curve to cup the arms. Performance - The Sonic/Ergo is designed to present minimal frontal area to create as little aerodynamic drag as possible. The main purpose of an aerobar is, of course, to get the rider into a fast position. Despite a fairly minimalist appearance, the Sonic/Ergo offers a comprehensive fit range for exactly this purpose. Fit Data - Armrest Offset: -70mm to -2.5mm in 7.5mm steps - Armrest Width: 124mm to 290mm in 18.5mm steps (With Extensions at 100mm) - Armrest Stack: 60mm (no riser kit) to 130mm in 5mm increments (With aftermarket Riser Kit) - The extension length and rotation can be easily adjusted using the top bolt. There are 100 distinct position options achievable just by moving the armrests. Combine that with the risers and this bar offers 1500 possible configurations. As a clip-on bar it is also possible to adjust the extension width and tilt easily. This is the most adjustable clip-on bar on the market (and in history). It is worth noting that our previous top-level clip-on aerobar, the J4/F35, offered 90 possible configurations. This highlights the significant step forward we’ve made with our new generation aerobars in allowing riders to precisely adjust their position. Origin - After we released the Supersonic (J5) as a premium bracket with market-leading fit options and versatility we wanted to bring the same kind of options to the rest of our range of brackets and thus aerobars. By simplifying the extension clamp and shifting the wing forward to the bar center line we were able to meet our targets. As a consequence of the simplification the Sonic is the lightest of our current brackets. - The Ergo armrest shares the flippable design of the rest of our new generation armrests. By swapping sides or rotating the armrests smaller increments of movement are achieved – making it simple to fine-tune a riders position or match the position from their previous aerobar or bike. Extensions - Extension Shape: A 50a extensions offer a 50° ski bend shape. The 50a offer a 7.5mm lateral shift per side. This allows the rider to get their hands narrower or wider without tilting the extensions so much that the shifters touch. - Bracket: Sonic - Clamp Diameter: 31.8mm (26.0 w/Shims) - Armrest: Ergo / 10mm Pads - Armrest Width: 124mm to 290mm in 18.5mm steps (with Extensions at 100mm) - Armrest Offset: -70mm to -2.5mm in 7.5mm steps - Armrest Stack: The minimum is 60mm and the bracket is compatible with our existing risers which add up to 130mm stack with (70mm of spacers added) - Weight: 559g

- Black carbon fiber weave headset spacers for tuning ride height, no logos - Kit includes 1-1/8" spacers: (15) 2.5mm, (25) 5mm, (16) 10mm, (2) 15mm, (4) 20mm

The perfect bike fit needs to blend slippery aerodynamics and a comfortable, stress-free body position while optimizing control over the bike. Top fitters are constantly devising new methods to maximize and balance these goals. Designed using feedback from top fitters, Zipp’s Vuka Carbon Extensions give you all the options needed to optimize your position and go for the win or your personal best: Vuka Carbon Evo 70 and 110 extensions Vuka Evo extensions decrease drag by starting airflow over the body sooner while keeping the arms and wrists in a comfortable, relaxed position. The Evo shape, with a 20mm inward roll and multi-radius bend, is now available for the first time in carbon, allowing for even more complex shaping and lighter weight. Vuka Race Carbon Extension The Vuka Race Carbon Extension was designed using data compiled from thousands of fit sessions with recreational and professional cyclists and triathletes by the world’s best fitters. The Vuka Race bend places the wrists at a more natural bend to help riders remain in their tuck to optimize aerodynamics. - Compatible with Vuka Clip, Vuka Aero and all 22.2 systems - Internal cable routing

- Zinc plated for durability - All screws grade 12.9 - 475 Pieces Kit contains: - M5 X 10 Button Head qty. 20 - M5 X 12 Button Head qty. 20 - M5 X 16 Button Head qty. 20 - M5 X 12 Socket, Zinc qty. 35 - M5 X 16 Socket, Zinc qty. 35 - M5 x 20 Socket, Zinc qty. 15 - M5 X 25 Socket, Zinc qty. 10 - M5 X 30 Socket, Zinc qty. 10 - M5 X 12 Flat Socket Head, Spd qty. 25 - M5 X 16 Flat Socket Head, Spd qty. 25 - M5 X 8 Flat Socket, Zinc qty. 20 - M5 Nut qty. 50 - M5 Nylock Nut, Zinc qty. 40 - M5 Acorn Nut, Zinc qty. 10 - M5 Flat Washer qty. 65 - M5 Oversized Flat Washer qty. 25 - M5 Lockwasher qty. 25 - M5 Toothed, Zinc qty. 25

Comprehensive shop kit for bottom bracket and cassette/freewheel spacing need. 139 pieces in a durable plastic storage box. Kit includes: - (20) 1.0mm FW Spacers - (10) 1.5mm FW Spacers - (10) 2.0mm FW Spacers - (10) NCS-4.5mm Cassette Spacers - (10) SHIM-.3MM Spacers - (10) SHIM-.5MM Spacers - (8) 0.5mm 24mm ID Spacers - (8) 1.0mm 24mm ID Spacers - (8) 2.5mm 24mm ID Spacers - (4) BB30-CLIPs - (4) BB30/PF30 Wave Washers - (4) GXP Wave Washers - (4) .7mm Bottom Bracket Spacers - (4) 1.8mm Bottom Bracket Spacers - (9) 2.5mm Bottom Bracket Spacers - (8) 0.5mm 30mm ID Spacers - (8) 1.0mm 30mm ID Spacers

RockShox Reverb Remote Assembly for A2 and B1 generation Reverb dropper seatposts. - Includes remote Lever, MMX clamp, Discrete Puck, 1500mm of new hose, new hose barb, and new hose strain relief - Works with A2 and B1 generation posts - A2 posts have a black return speed adjuster on the remote and no laser-etched logos on stanchion by the saddle cradle. - B1 posts have a black return speed adjuster on the remote and "ROCKSHOX" laser-etched logos on stanchion by the saddle cradle.

Comfort armrest set comprises pads and cradles and was original equipment on Ventus, use to upgrade Aura, Brezza II Team, and Mistral.

Compact armrest set comprises pads and cradles for Aura, Brezza II Team, Mistral, and Ventus.

RockShox Reverb Remote Assembly for A1 generation Reverb and Reverb Stealth. - Includes remote Lever, MMX clamp, 1500mm of new hose, new hose barb, new strain relief - For "A1" designated posts, 2010-2012 - A1 posts have a silver return speed adjuster on the remote and no laser-etched logos on stanchion by the saddle cradle

3T's S-Bend Aero Extensions are made of light, stiff carbon and feature ergonomic bends to keep your wrists comfortable during your time against the clock. - Standard 22.2-mm diameter - 305mm maximum extension from center line of bar clamp

3T's Wrist Comfort Bend Aero Extensions are made of light, stiff carbon and feature large ergonomic bends to keep your wrists as comfortable as possible and ensure a sturdy grip during your time against the clock. - Standard 22.2-mm diameter - 305mm maximum extension from center line of bar clamp

3T's Straight Aero Extensions are made of light, stiff carbon and feature no bends for an ultra low position during your time against the clock. - Standard 22.2-mm diameter - 305mm maximum extension from center line of bar clamp

- Includes stock replacement retainers for headsets, bottom brackets and hubs - Headsets: (8) 5/32"x22, (8) 5/32"x16, (8) 3/16"x15, (24) 5/32"x20; - Bottom brackets: (12) 1/4"x9, (16) 5/16"x9, (16) 5/16"x10 - Hubs: (8) 3/16"x7, (16) 1/4"x7

Replacement clamp kit for Vola PRO and Clip on Pro/Team aerobars.

K-EDGE MTB Chain Guide is built to be the strongest and lightest solution to withstand the pedaling force of a derailed single ring chain in World Cup race conditions. - Full-cage design for chain retention under the most abusive cross situations - Braze-on mount and braze-on adapter clamp compatible - Fully adjustable for height, center-line, and angle - Optimized for 10 and 11spd drivetrains - CNC Machined from 6061-T6 Aluminum (no plastic parts) - Stainless Steel Hardware - Weight: 60.8 grams (excluding braze-on adapter clamp) - Compatibility: Single-ring bikes; frames with integrated braze-on front derailleur mount; also compatible with braze-on adapter clamps. All necessary hardware included - Optimized for 34T to 44T Chain Rings - “Hard to fit kits” may be needed for current applications, please contact Info@k-edge.com - Made in Boise, Idaho, USA - Lifetime Guarantee against material or manufacture defects. Damages due to abuse or crashing excluded

EPS cable guide magnets are required for internally routing EPS wires. - Includes: wire, metal cable, and magnet

This assortment of chainring spacers contains 120 pcs. in a clear plastic storage box. Kit includes: - (20) 0.6mm - (20) 1.2mm - (5) 2mm - (5) 3.8mm - (5) 2.2mm - (5) 3mm - (5) 3.5mm - (10) 4mm - (10) 4.3mm - (10) 4.6mm - (10) 5mm - (5) 5.3mm - (5) 7.1mm - (5) 8.3mm